**** BEGIN LOGGING AT Sat Feb 3 13:04:57 2007
Feb 03 13:05:14 <bluetape> eh?
Feb 03 13:05:26 <hammer2> lol my point exactly
Feb 03 13:05:32 <hammer2> doesnt make sense
Feb 03 13:05:45 <hammer2> what about same but as 1
Feb 03 13:05:49 <hammer2> insted of 2
Feb 03 13:05:58 <bluetape> you don't have an eth1
Feb 03 13:06:33 <hammer2> shows 1 and 2 in pastebin
Feb 03 13:06:41 <hammer2> http://pastebin.ca/338842
Feb 03 13:06:43 <bluetape> I see 0 and 2
Feb 03 13:06:55 <hammer2> http://pastebin.ca/338842
Feb 03 13:06:57 <bluetape> there's only 0 and 2 now
Feb 03 13:06:57 <hammer2> oops
Feb 03 13:07:11 <hammer2> eth1 NOT READY! ESSID:off/any
Feb 03 13:07:23 <bluetape> it's not there anymore
Feb 03 13:08:05 <hammer2> ok
Feb 03 13:08:18 <bluetape> does just ifconfig eth2 up give an error?
Feb 03 13:08:30 <hammer2> looking
Feb 03 13:09:32 <hammer2> http://pastebin.ca/338852
Feb 03 13:11:04 <bluetape> you need ifconfig -a to see it
Feb 03 13:11:33 <bluetape> just do ifconfig eth2 up by itself
Feb 03 13:12:47 <hammer2> ok so open a fresh term then
Feb 03 13:12:49 <hammer2> ?
Feb 03 13:13:01 <hammer2> then ifconfig eth2 up
Feb 03 13:13:41 <hammer2> SIOCSIFFLAGS: No such file or directory
Feb 03 13:13:45 <hammer2> well what the heck
Feb 03 13:14:01 <hammer2> doesnt make any sense
Feb 03 13:16:36 <bluetape> does just ifconfig eth2 show anything?
Feb 03 13:17:06 <hammer2> ya shows alot
Feb 03 13:17:08 <hammer2> lol
Feb 03 13:17:12 <hammer2> check it out
Feb 03 13:17:35 * linmax_____ is now known as linmax
Feb 03 13:17:57 <hammer2> could be wrong but i dont even see an error
Feb 03 13:18:01 <hammer2> http://pastebin.ca/338860
Feb 03 13:18:12 <hammer2> could it be because i am on my cable line?
Feb 03 13:18:39 <hammer2> so when we did up it wont go because im on wired cable?
Feb 03 13:18:40 <bluetape> probably not
Feb 03 13:19:00 <hammer2> i dont see an error there
Feb 03 13:19:11 <hammer2> before said not ready
Feb 03 13:19:17 <hammer2> now it dont
Feb 03 13:20:36 <bluetape> yeah, because you're using a different driver now
Feb 03 13:21:06 <hammer2> wich is good right
Feb 03 13:21:24 <bluetape> yeah, that was the whole point
Feb 03 13:21:38 <hammer2> lspci says 07:00.0 Network controller: Intersil Corporation ISL3890 [Prism GT/Prism Duette] /ISL3886 [Prism Javelin/Prism Xbow] (rev 01)
Feb 03 13:22:38 <hammer2> what if i unplug and went dhclient eth2
Feb 03 13:22:41 <bluetape> you should use your distro's config tools to try to config the interface now
Feb 03 13:22:52 <bluetape> that won't work because you need to associate to an AP first
Feb 03 13:23:03 <hammer2> ok how do i get there
Feb 03 13:23:06 <bluetape> though dhclient might be able to take it up properly
Feb 03 13:23:07 <hammer2> the tool things
Feb 03 13:23:11 <bluetape> so maybe you should try that
Feb 03 13:23:16 <hammer2> ok ill try
Feb 03 13:26:17 <bluetape> and then do iwlist eth2 scan in another window while dhclient is running
Feb 03 13:26:26 * koreth has quit ("Ex-Chat")
Feb 03 13:26:26 <the_hammer> i got unknown command on that
Feb 03 13:26:34 <the_hammer> but ill paste ya a strange output again in a sec just connecting back to wired net
Feb 03 13:27:01 <hammer2> test
Feb 03 13:27:52 <hammer2> http://pastebin.ca/338891
Feb 03 13:28:21 * koreth (n=koreth@lns-bzn-50f-62-147-185-94.adsl.proxad.net) has joined #prism54
Feb 03 13:29:56 <hammer2> duh i think i need sudo then try
Feb 03 13:30:05 <hammer2> ill try 1 more time
Feb 03 13:30:13 <hammer2> seen permission denied errors
Feb 03 13:30:25 <bluetape> stay in root then
Feb 03 13:30:45 <hammer2> sudo su
Feb 03 13:35:15 <the_hammer> getting that no such dir error
Feb 03 13:35:58 <the_hammer> network is down
Feb 03 13:35:58 * koreth has quit (Client Quit)
Feb 03 13:35:58 <the_hammer> what about a reboot and try again then?
Feb 03 13:35:58 <the_hammer> no working leasses in persistent database
Feb 03 13:35:58 <the_hammer> -sleeping
Feb 03 13:35:58 <bluetape> maybe
Feb 03 13:35:58 <bluetape> well
Feb 03 13:35:58 <bluetape> lets see your dmesg first
Feb 03 13:35:58 <the_hammer> k
Feb 03 13:36:08 <hammer2> http://pastebin.ca/338899
Feb 03 13:36:24 <hammer2> tets
Feb 03 13:36:27 Tcl interface unloaded
Feb 03 13:36:27 Python interface unloaded
**** ENDING LOGGING AT Sat Feb 3 13:36:27 2007
**** BEGIN LOGGING AT Sat Feb 3 13:36:48 2007
Feb 03 13:36:48 * Now talking on #prism54
Feb 03 13:36:48 * Topic for #prism54 is: Main site: http://prism54.org || Don't ask to ask, just ask your question (but be prepared to wait a while) || for USB and PCI (incl. PCMCIA) softmac cards use the p54 driver (wireless-dev git tree on kernel.org) || Information about netgear's WG511s: http://daemonizer.de/prism54/wg511/
Feb 03 13:36:48 * Topic for #prism54 set by linmax at Thu Dec 21 16:22:16 2006
Feb 03 13:36:48 * #prism54 :[freenode-info] help freenode weed out clonebots, please register your IRC nick and auto-identify: http://freenode.net/faq.shtml#nicksetup
Feb 03 13:36:57 <hammer2> http://pastebin.ca/338899
Feb 03 13:37:05 <bluetape> oh
Feb 03 13:37:09 <bluetape> you don't have the firmware installed
Feb 03 13:37:45 <the_hammer> ok now what do i need
Feb 03 13:37:59 <bluetape> mkdir /lib/firmware then get 2.7.0.0, rename it to isl3886_pci and put it in /lib/firmware
Feb 03 13:38:03 <the_hammer> brb just grabbin a cooffee and turning heat up
Feb 03 13:39:58 <hammer2> root@lappy:/# mkdir /lib/firmware
Feb 03 13:39:58 <hammer2> mkdir: cannot create directory `/lib/firmware': File exists
Feb 03 13:39:58 <hammer2> root@lappy:/#
Feb 03 13:40:32 <hammer2> where do i grab that file...from the links in chan here?
Feb 03 13:41:14 <hammer2> nope
Feb 03 13:41:20 <hammer2> http://prism54.org/fullmac.html dont wnat that lol
Feb 03 13:41:55 <hammer2> not sure where to get that from
Feb 03 13:42:27 <hammer2> can i apt-cache search?
Feb 03 13:43:00 <bluetape> no
Feb 03 13:43:21 <bluetape> http://prism54.org/firmware/2.7.0.0.arm
Feb 03 13:43:33 <bluetape> and if /lib/firmware exists, delete it
Feb 03 13:44:17 <hammer2> stupid kate opens
Feb 03 13:44:30 <hammer2> so save as 2.7.0.0.arm
Feb 03 13:44:44 <bluetape> yeah
Feb 03 13:45:16 <hammer2> The file file:///home/hammer/Desktop/2.7.0.0.arm is a binary, saving it will result in a corrupt file.
Feb 03 13:45:21 <hammer2> do it anyway?
Feb 03 13:45:28 <bluetape> just wget it
Feb 03 13:45:35 <hammer2> how i do that
Feb 03 13:45:55 <bluetape> wget http://prism54.org/firmware/2.7.0.0.arm
Feb 03 13:46:25 <hammer2> 100%[==================================================================================================>] 29,024 41.75K/s
Feb 03 13:46:25 <hammer2> 13:46:07 (41.67 KB/s) - `2.7.0.0.arm' saved [29024/29024]
Feb 03 13:47:36 <hammer2> are ya sure i should delete /lib/firmware
Feb 03 13:47:44 <hammer2> i found this and a ton of files
Feb 03 13:47:48 <hammer2> /lib/firmware/2.6.17-10-generic
Feb 03 13:48:14 <bluetape> it's not a file then
Feb 03 13:48:26 <hammer2> err folder sorry
Feb 03 13:48:26 <bluetape> don't touch it then
Feb 03 13:48:30 <hammer2> k
Feb 03 13:48:56 <bluetape> just mv 2.7.0.0.arm /lib/firmware/isl3886_pci
Feb 03 13:49:20 <hammer2> root@lappy:/# mv 2.7.0.0.arm /lib/firmware/isl3886_pci
Feb 03 13:49:20 <hammer2> root@lappy:/#
Feb 03 13:49:27 <bluetape> ok
Feb 03 13:49:28 <hammer2> cd into it?
Feb 03 13:49:44 <bluetape> now ifconfig eth2 up
Feb 03 13:50:15 <hammer2> root@lappy:/# ifconfig eth2 up
Feb 03 13:50:15 <hammer2> root@lappy:/#
Feb 03 13:50:21 <bluetape> about time
Feb 03 13:50:25 <bluetape> iwlist eth2 scan
Feb 03 13:50:26 <hammer2> lol
Feb 03 13:50:49 <hammer2> root@lappy:/# iwlist eth2 scan
Feb 03 13:50:49 <hammer2> eth2 No scan results
Feb 03 13:50:49 <hammer2> root@lappy:/#
Feb 03 13:51:15 <bluetape> hrm
Feb 03 13:51:17 <bluetape> dmesg?
Feb 03 13:51:28 <bluetape> you might need the older firmware
Feb 03 13:52:32 <hammer2> http://pastebin.ca/338929
Feb 03 13:53:00 <bluetape> ah, now it's unable to boot
Feb 03 13:53:15 <bluetape> take your card out, plug it back in, try to up and scan again
Feb 03 13:53:16 <hammer2> but
Feb 03 13:53:23 <hammer2> i got a green light on my card
Feb 03 13:53:35 <hammer2> thats good i havent seen it since the last day we got it up
Feb 03 13:53:47 <hammer2> likely cuz im on my wire
Feb 03 13:53:49 <hammer2> ?
Feb 03 13:53:58 <bluetape> no
Feb 03 13:54:23 <hammer2> it cant connect if im on wired i dont think tho?
Feb 03 13:54:35 <bluetape> it can connect
Feb 03 13:54:39 <bluetape> it just won't work quite right
Feb 03 13:54:45 <hammer2> ok
Feb 03 13:54:47 <bluetape> but it's not connecting yet
Feb 03 13:55:02 <hammer2> what about a reboot just for nthe heck of it
Feb 03 13:55:16 <hammer2> this is as close as ive been in a week
Feb 03 13:55:18 <bluetape> that's not gonna help
Feb 03 13:55:22 <hammer2> hearts racing lol
Feb 03 13:55:41 <bluetape> just take the card out, plug it back in, and try uping and scaning again
Feb 03 13:56:04 <hammer2> ok
Feb 03 13:56:39 <hammer2> root@lappy:/# ifconfig eth2 up
Feb 03 13:56:39 <hammer2> root@lappy:/#
Feb 03 13:56:57 <bluetape> yeah yeah
Feb 03 13:57:05 <bluetape> try scanning
Feb 03 13:57:06 <hammer2> iwlist eth2 scan?
Feb 03 13:57:08 <hammer2> k
Feb 03 13:57:56 <hammer2> same
Feb 03 13:58:01 <hammer2> unable to boot device
Feb 03 13:58:56 <hammer2> wait
Feb 03 13:59:35 <hammer2> opened a new term root and did again different outpput
Feb 03 13:59:39 <hammer2> http://pastebin.ca/338963
Feb 03 14:00:16 <hammer2> no errors :)
Feb 03 14:01:08 <bluetape> k
Feb 03 14:01:11 <bluetape> your driver is working now
Feb 03 14:01:19 <bluetape> configuration is now your problem
Feb 03 14:01:27 <hammer2> so reboot and see if it connects
Feb 03 14:01:43 <hammer2> ok conf
Feb 03 14:01:45 <bluetape> you should move islsm.ko to the prism54 directory
Feb 03 14:01:50 <bluetape> and depmod -a
Feb 03 14:01:55 <bluetape> that should get it to autoload
Feb 03 14:02:02 <hammer2> ok how i do that
Feb 03 14:02:21 <bluetape> islsm.ko is in the islsm directory
Feb 03 14:04:32 <hammer2> trying to manully get there
Feb 03 14:04:37 <hammer2> its in /lib right
Feb 03 14:08:24 <hammer2> so i go here /lib/firmware/isl3886_pci
Feb 03 14:09:07 <bluetape> what?
Feb 03 14:09:07 <hammer2> dam bin ery thing again
Feb 03 14:09:15 <bluetape> what are you doing
Feb 03 14:09:16 <bluetape> don't touch that
Feb 03 14:09:19 <hammer2> trying to figure out how to do what ya said to do
Feb 03 14:09:20 <bluetape> you got it working
Feb 03 14:09:34 <hammer2> i clicked out of there
Feb 03 14:09:50 <hammer2> soon as i opened the dir it pop uped right away
Feb 03 14:10:00 <bluetape> just move the islsm.ko in the islsm directory on your desktop to /lib/module/kernelversion/kernel/drivers/net/wireless/prism54/
Feb 03 14:10:00 <hammer2> didnt see a folder just a box says dont save
Feb 03 14:10:06 <hammer2> lol so got outta there
Feb 03 14:14:06 <hammer2> /lib/modules/2.6.17-10-generic/kernel/drivers/net/wireless/prism54 to here right?
Feb 03 14:14:27 <hammer2> ok now just trying to figure how to do in term
Feb 03 14:14:33 <hammer2> mv i know =move
Feb 03 14:15:40 <hammer2> dam it
Feb 03 14:15:51 <hammer2> root@lappy:/# ls islsm
Feb 03 14:15:51 <hammer2> ls: islsm: No such file or directory
Feb 03 14:15:55 <hammer2> trying to cd into it
Feb 03 14:16:24 <hammer2> its in firmware folder isnt it?
Feb 03 14:16:55 <bluetape> it's in your /home/hammer/Desktop directory or something like that
Feb 03 14:16:59 <hammer2> root@lappy:/# ls islsm
Feb 03 14:16:59 <hammer2> ls: islsm: No such file or directory
Feb 03 14:17:05 <hammer2> ahh
Feb 03 14:17:33 <hammer2> so i can point click it then
Feb 03 14:21:01 <hammer2> root@lappy:/lib/modules/2.6.17-10-generic/kernel/drivers/net/wireless/prism54# dir
Feb 03 14:21:01 <hammer2> islsm.ko
Feb 03 14:21:01 <hammer2> root@lappy:/lib/modules/2.6.17-10-generic/kernel/drivers/net/wireless/prism54#
Feb 03 14:21:08 <hammer2> wow thats tricky a bit
Feb 03 14:21:26 <hammer2> ows that?
Feb 03 14:21:29 <hammer2> hows*
Feb 03 14:23:18 <bluetape> good
Feb 03 14:23:20 <bluetape> depmod -a
Feb 03 14:23:22 <bluetape> bbl
Feb 03 14:23:53 <hammer2> root@lappy:/# depmod -a
Feb 03 14:23:53 <hammer2> root@lappy:/#
Feb 03 14:30:06 Tcl interface unloaded
Feb 03 14:30:06 Python interface unloaded
**** ENDING LOGGING AT Sat Feb 3 14:30:06 2007
**** BEGIN LOGGING AT Sat Feb 3 14:39:12 2007
Feb 03 14:39:12 * Now talking on #prism54
Feb 03 14:39:12 * Topic for #prism54 is: Main site: http://prism54.org || Don't ask to ask, just ask your question (but be prepared to wait a while) || for USB and PCI (incl. PCMCIA) softmac cards use the p54 driver (wireless-dev git tree on kernel.org) || Information about netgear's WG511s: http://daemonizer.de/prism54/wg511/
Feb 03 14:39:12 * Topic for #prism54 set by linmax at Thu Dec 21 16:22:16 2006
